| OCR Text |
Show films, manufacturers* charts, etc. Units of each kind of drive are disassembled, inspected and reassembled according to manufacturer's recommended procedure in the shop. (3). 72. Automatic Drive TransmissionsContinuation of Automatic Drive Transmissions 71. (3). 73. Automatic Drive TransmissionsContinuation of Automatic Drive Transmissions 72. (3). 74. Automotive Electricity Theory, construction, and servicing storage batteries, generators and their control systems ; wiring systems, ignition systems, and starting motors and their controls. (3). 75. Carburetion Theory, construction, and methods of servicing carburetors and other carburetion units. (3). 76. CarburetionContinuation of Carburetion 75. (3). 77. Motor Tune-UpOperations necessary to restore to factory specification the following units: Ignition, generators and controls, battery, starter, carburetor, and fuel pump; compression with the use of tune-up equipment. (3). 78. Motor Tune-UpContinuation of Motor Tune-Up 77. (3). 81. Automotive Brake SystemsPower brakes, hydraulic principles as they apply to brakes; operation and reconditioning methods of all types of brake systems. (3). 82. Wheel Alignment:Theory, construction, methods of adjusting and correcting all types of front wheel suspension; classroom work and shop work covering wheel balancing, steering gear service, and other related parts. A W S (3). DIESEL Courses of Instruction 71. Automotive Diesel Repair and Service Mechanical construction of two-cycle and four-cycle diesel engines used in automotive service; problems of overhauling the diesel engine; its maintenance and operation. (3). 72. Automotive Diesel Repair and ServiceContinuation of Automotive Diesel Repair and Service 71. (3). 73. Automotive Diesel Repair and ServiceContinuation of Automotive Diesel Repair and Service 72. (3). 74. Automotive Diesel Repair and ServiceContinuation of Automotive Diesel Repair and Service 73. (3). 75. Automotive Diesel Repair and ServiceContinuation of Automotive Diesel Repair and Service 74. (3). 76. Automotive Diesel Repair and ServiceContinuation of Automotive Diesel Repair and Service 75. (8). INDUSTRIAL DRAFTING The classes listed in the day section of Industrial Drafting will be offered in the Evening School; however, in a class where 4 credit hours are given, two consecutive quarters of work will be required to complete that particular course. (See day section.) ELECTRONICS The classes listed in the day section of Electronics will be offered in the Evening School; however, in a class where 4 credit hours are given, two consecutive quarters of work will be required to complete that particular course. (See day section.) INDUSTRIAL ELECTRICITY (For Plant Maintenance Electricians) Courses of Instruction 81. Fundamentals of ElectricityElectron theory; Ohms law; series and parallel circuits; Kirchofs laws; work, power, torque, and transmission of power. (3). 82. Conductors and MagnetismCurrent carrying capacity of conductors, voltage drop, and conductivity magnets and magnetic fields; reluctance, permability and flux density; magnetic circuits and magnetic applications. (3). 83. Armature WindingVoltage in a rotating coil; lap and wave winding; paths and multiplicity; selection of type of winding; slots, segments, coils, and pitch, and armature testing. (3). 84. Direct Current Motors, Generators and Controllers Principles of the motor torque, power, and armature reaction; series, shunt, and compound motors; speed regulation and rotation of motors; construction of generators; methods of field ex-citation ; commutation and commutating poles; series, shunt, and compound generators manual and magnetic controllers; low voltage and overload protection; dynamic braking and reversing controllers. (3). 85. Alternating Current and Circuits Generation of a sine wave; average and effective values; vector representation; resistance, inductance, and capacity in series and parallel circuits ; impedance, resonance, and power factor problems and correction; power and reactive power in AC circuits. A W S (3). 86. Transformers and Polyphase SystemsEfficiency of transmission; transformer principles and construction; types of transformers; losses and efficiency; two- and three-phase |
